Brownells Deutschland - Einer der größten Lieferanten für Waffenteile, Büchsenmacherwerkzeug & Schießsportzubehör Deutschland

EGW
TAURUS G2, G3, PT709 AND TX22 VORTEX VIPER/VENOM SIGHT MOUNT

841370117543 296000651
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with the mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
76.9 76.9 1 EUR
Artikel-Nr.: 296000651
EGW SIGHT MOUNT FOR VORTEX VIPER/VENOM FITS TAURUS G2/G3 BLACK
Herstellerproduktnummer: 49291 841370117543 EGW Red-Dot-Visiere sollen von links nach rechts installiert werden (mit der Mündung nach vorne gerichtet). Die Schwalbenschwanzführung hat eine progressive Verjüngung, um die Installation zu erleichtern. Einfach das hintere Visier deiner Waffe entfernen und durch die Montage ersetzen, um dein Vortex Viper/Venom, Burris FastFire oder Docter Red-Dot-Visier zu montieren. Du kannst die Montage jederzeit abnehmen und dein hinteres Visier wieder anbringen. Montagematerial ist enthalten. Installationsanweisungen: Entferne das hintere Visier* Installiere die EGW Sight Mount in der Schwalbenschwanzführung Ziehe die Stellschraube fest (falls zutreffend) Platziere das Red-Dot-Visier auf der EGW Sight Mount (ein kleines Stück Papier zwischen Red-Dot-Visier und Sight Mount zu legen, erleichtert das Entfernen und hält Loctite vom Red-Dot-Visier fern.) Trage blaues Loctite auf die mitgelieferten Montageschrauben auf Ziehe die Montageschrauben mit 15in/lbs an 2 Zylinderkopfschrauben - Für Vortex Viper und Venom Visiere bereitgestellt 2 Senkkopfschrauben - Für Burris FastFire und Docter Visiere bereitgestellt Die mit dieser Montage gelieferten Schrauben benötigen einen 5/64'' Inbusschlüssel zur Installation. Eine Modifikation deiner Schusswaffe kann die Garantie des Herstellers ungültig machen. Dieses Produkt sollte von einem qualifizierten Büchsenmacher installiert und überprüft werden. Für Schäden oder Verletzungen, die durch eine unsachgemäße Installation oder Verwendung dieses Produkts entstehen könnten, wird keine Haftung übernommen.
76.9 EUR 3 76,90 € *
Lieferzeit ca. 14-21 Tage.
3 Stk. im Großlager
Eigenschaften: Art: Tactical Basenanzahl: 1-Piece Farbe: Black Hersteller/Modell: Taurus Material: Aluminum Modell: PT-111, G3, G2C, TX22, PT-740, PT-709, PT-140 G2, G2S

Eigenschaften

Art: Tactical Basenanzahl: 1-Piece Farbe: Black Hersteller/Modell: Taurus Material: Aluminum Modell: PT-740,G2S,PT-111,PT-140 G2,TX22,PT-709,G3,G2C Versandgewicht: 0,045kg Versandhöhe: 25mm Versandbreite: 76mm Versandlänge: 140mm

Artikeldetails

Made in USA



EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with the mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
Newsletter