Brownells Deutschland - Einer der größten Lieferanten für Waffenteile, Büchsenmacherwerkzeug & Schießsportzubehör Deutschland

EGW
S&W M&P TRIJICON RMR SIGHT MOUNT

841370116812 296000567
Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.780 Overall Width: 1.1" Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw Red Dot Fitment: Trijicon RMR This mount will fit: Smith & Wesson M&P Full Size Smith & Wesson M&P 2.0 Full Size Smith & Wesson M&P 22 Full Size Smith & Wesson M&P Compact* Smith & Wesson M&P 2.0 Compact* Smith & Wesson SD9VE Smith & Wesson SD40VE This mount does not fit: Smith & Wesson M&P Shield (Our mount is too wide to fit the Shield) Smith & Wesson M&P Shield EZ .380 Smith & Wesson SW9VE Smith & Wesson SW40VE Smith & Wesson M&P C.O.R.E Series *Will not fit the M&P .22 Compact.  Smith and Wesson's rear sight dovetails are known to vary in dimensions. Our sights are made to the same tolerances. Some users may have trouble installing our plate on their slide due to the varying tolerances in your slides. Please keep this in mind when ordering.These mounts should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs *Rear sight pusher tool highly recommended*
76.9 76.9 1 EUR
Artikel-Nr.: 296000567
EGW S&W M&P Trijicon RMR Sight Mount
Herstellerproduktnummer: 49508 841370116812 Material: 7075 Aluminium Beschichtung: Matte Black Hardcoat Gesamtlänge: 1,780 Zoll Gesamtbreite: 1,1" Montagezubehör: (2) 6-32 Flachkopfschrauben, (1) 6-32 X 3/16 Set-Schraube Red Dot Anpassung: Trijicon RMR Diese Montage passt für: Smith & Wesson M&P Full Size Smith & Wesson M&P 2.0 Full Size Smith & Wesson M&P 22 Full Size Smith & Wesson M&P Compact* Smith & Wesson M&P 2.0 Compact* Smith & Wesson SD9VE Smith & Wesson SD40VE Diese Montage passt nicht für: Smith & Wesson M&P Shield (Unsere Montage ist zu breit für den Shield) Smith & Wesson M&P Shield EZ .380 Smith & Wesson SW9VE Smith & Wesson SW40VE Smith & Wesson M&P C.O.R.E Series *Passt nicht für den M&P .22 Compact. Die Kimmenaussparungen von Smith and Wesson sind bekannt für ihre variierenden Abmessungen. Unsere Visiere werden mit den gleichen Toleranzen hergestellt. Einige Benutzer könnten Probleme haben, unsere Platte aufgrund der unterschiedlichen Toleranzen in ihren Schlitten zu installieren. Bitte beachte dies bei der Bestellung.Diese Montagen sollten von einem qualifizierten Büchsenmacher installiert und überprüft werden. Wir übernehmen keine Haftung für Schäden oder Verletzungen, die durch unsachgemäße Installation oder Verwendung dieses Produkts entstehen können. Einfach das hintere Visier deiner Waffe entfernen und durch unsere Montage ersetzen, um dein Trijicon RMR Red Dot Visier anzubringen. Keine Änderungen erforderlich. Du kannst unsere Montage jederzeit entfernen und dein hinteres Visier wieder anbringen. Montagezubehör inbegriffen. Installationsanleitung Entferne das hintere Visier* Installiere die EGW Sight Mount in der Kimmenaussparung Ziehe die Set-Schraube fest (falls zutreffend) Platziere das Red Dot Visier auf der EGW Sight Mount (ein kleines Stück Papier zwischen dem Red Dot Visier und der Montage erleichtert die Entfernung und hält Loctite vom Red Dot Visier fern.) Wende blaues Loctite auf die mitgelieferten Montageschrauben an Ziehe die Montageschrauben mit einem Drehmoment von 15in/lbs fest *Werkzeug zum Entfernen des hinteren Visiers wird dringend empfohlen*
76.9 EUR 6 76,90 € *
Lieferzeit ca. 14-21 Tage.
6 Stk. im Großlager
Eigenschaften: Art: Tactical Basenanzahl: 1-Piece Farbe: Black Hersteller/Modell: Smith & Wesson Material: Aluminum Modell: M&P 22, M&P Compact, M&P 2.0 Compact

Eigenschaften

Art: Tactical Basenanzahl: 1-Piece Farbe: Black Hersteller/Modell: Smith & Wesson Material: Aluminum Modell: M&P 2.0 Compact,M&P 22,M&P Compact Versandgewicht: 0,033kg Versandhöhe: 25mm Versandbreite: 76mm Versandlänge: 127mm

Artikeldetails

Made in USA



Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.780 Overall Width: 1.1" Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw Red Dot Fitment: Trijicon RMR This mount will fit: Smith & Wesson M&P Full Size Smith & Wesson M&P 2.0 Full Size Smith & Wesson M&P 22 Full Size Smith & Wesson M&P Compact* Smith & Wesson M&P 2.0 Compact* Smith & Wesson SD9VE Smith & Wesson SD40VE This mount does not fit: Smith & Wesson M&P Shield (Our mount is too wide to fit the Shield) Smith & Wesson M&P Shield EZ .380 Smith & Wesson SW9VE Smith & Wesson SW40VE Smith & Wesson M&P C.O.R.E Series *Will not fit the M&P .22 Compact.  Smith and Wesson's rear sight dovetails are known to vary in dimensions. Our sights are made to the same tolerances. Some users may have trouble installing our plate on their slide due to the varying tolerances in your slides. Please keep this in mind when ordering.These mounts should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs *Rear sight pusher tool highly recommended*
Newsletter