Brownells Deutschland - Einer der größten Lieferanten für Waffenteile, Büchsenmacherwerkzeug & Schießsportzubehör Deutschland

EGW
RUGER PC CARBINE TRIJICON RMR SIGHT MOUNT

841370116423 296000590
Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.780" Overall Width: 1.1" Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw Red Dot Fitment: Trijicon RMR, Holosun HS507C This mounts fits: Baby Desert Eagle (Post 2006) EAA Witness Elite Match This mount does not fit: Rock Island 1911s Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Flat Head Cap Screws - Provided for Trijicon RMR The screws that are included with this mount require a 5/64'' allen wrench for installation.
77.9 77.9 1 EUR
Artikel-Nr.: 296000590
EGW Ruger® PC Carbine Trijicon RMR Sight Mount
Herstellerproduktnummer: 49531 841370116423 Material: 7075 Aluminium Beschichtung: Mattschwarz Hardcoat Gesamtlänge: 1,780" Gesamtbreite: 1,1" Montagematerial: (2) 6-32 Flachkopfschrauben, (1) 6-32 x 3/16 Zoll Gewindestift Roter-Punkt-Kompatibilität: Trijicon RMR, Holosun HS507C Diese Montage passt für: Baby Desert Eagle (nach 2006) EAA Witness Elite Match Diese Montage passt nicht für: Rock Island 1911s Einfach das hintere Visier deiner Waffe entfernen und durch unsere Montage ersetzen, um dein Trijicon RMR Rotpunktvisier zu montieren. Keine Änderungen erforderlich. Du kannst unsere Montage jederzeit entfernen und dein hinteres Visier wieder anbringen. Montagematerial inklusive. Installationsanweisungen Entferne das hintere Visier* Installiere die EGW Visiermontage im Schwalbenschwanz Ziehe die Gewindestiftschraube fest (falls zutreffend) Platziere das Rotpunktvisier auf der EGW Visiermontage (ein kleines Stück Papier zwischen Rotpunktvisier und Montage erleichtert die Demontage und hält Loctite fern vom Rotpunktvisier.) Trage blaues Loctite auf die mitgelieferten Montageschrauben auf Ziehe die Montageschrauben mit einem Drehmoment von 15in/lbs fest 2 Flachkopfschrauben - mitgeliefert für Trijicon RMR Die Schrauben, die mit dieser Montage geliefert werden, benötigen einen 5/64'' Inbusschlüssel zur Installation.
77.9 EUR 3 77,90 € *
Lieferzeit ca. 14-21 Tage.
3 Stk. im Großlager
Eigenschaften: Art: Tactical Basenanzahl: 1-Piece Farbe: Black Hersteller/Modell: Ruger Material: Aluminum Modell: PC Carbine

Eigenschaften

Art: Tactical Basenanzahl: 1-Piece Farbe: Black Hersteller/Modell: Ruger Material: Aluminum Modell: PC Carbine Versandgewicht: 0,037kg Versandhöhe: 25mm Versandbreite: 89mm Versandlänge: 140mm

Artikeldetails

Made in USA



Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.780" Overall Width: 1.1" Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw Red Dot Fitment: Trijicon RMR, Holosun HS507C This mounts fits: Baby Desert Eagle (Post 2006) EAA Witness Elite Match This mount does not fit: Rock Island 1911s Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Flat Head Cap Screws - Provided for Trijicon RMR The screws that are included with this mount require a 5/64'' allen wrench for installation.
Newsletter