Brownells Deutschland - Einer der größten Lieferanten für Waffenteile, Büchsenmacherwerkzeug & Schießsportzubehör Deutschland
100045341
Ted Yost developed and made these sights several years ago and after a long absence from the marketplace they are once again available from Harrison Design. These sights can be used to rescue a slide from mis-cut front dovetails. They have an oversize dovetail base featuring nominal dimensions of .085"" depth, .375"" width with a 65 dovetail angle. That's big enough to rescue most any sort of ugliness and butchery. The blade is .275"" tall X .630"" long X .125 wide. The vertical rill pin has been omitted so you can match it's location to wherever your slide's hole location is located. The dovetail base is .625"" wide, so it can be blended to the top of your slide, or youcan cut the sides back for the appearance you want. A radius is machined at the point where the blade joins the dovetail base, strengthening the sight appreciably. This is a part that every gunsmith should keep 2 or 3 of on hand as it can get you out of a jam is a slip up is made. It can be cut down and made into other sight blanks as well. It's a great tool for your toolbox you use to be a great gunsmith!  
37.9 37.9 1 EUR
Artikel-Nr.: 100045341
HARRISON DESIGN & CONSULTING RESCUE FRONT SIGHT BLANK, .375 X 65 X .085
Herstellerproduktnummer: HD013 Ted Yost hat diese Visiere vor einigen Jahren entwickelt und hergestellt, und nach langer Abwesenheit auf dem Markt sind sie nun wieder über Harrison Design erhältlich. Diese Visiere können verwendet werden, um eine Schiebe mit falsch geschnittenen Front-Dovetails zu retten. Sie haben eine übergroße Dovetail-Basis mit den nominalen Abmessungen von 0,085'' Tiefe, 0,375'' Breite mit einem 65-Grad-Dovetail-Winkel. Das ist groß genug, um fast jede Art von Unschönheiten und Verstümmelungen zu korrigieren. Die Klinge ist 0,275'' hoch X 0,630'' lang X 0,125 breit. Der vertikale Rill-Pin wurde weggelassen, so dass du dessen Position an die Lochposition deiner Schiebe anpassen kannst. Die Dovetail-Basis ist 0,625'' breit, sodass sie an die Oberseite deiner Schiebe angeglichen werden kann, oder du kannst die Seiten zurück schneiden, um das Aussehen zu erhalten, das du möchtest. Ein Radius ist an der Stelle, wo die Klinge auf die Dovetail-Basis trifft, maschinell bearbeitet, was das Visier deutlich verstärkt. Dies ist ein Teil, das jeder Büchsenmacher immer 2 oder 3 auf Lager haben sollte, da es aus der Patsche helfen kann, wenn ein Fehler passiert. Es kann heruntergeschnitten und in andere Visierblanks umgewandelt werden. Es ist ein großartiges Werkzeug für deine Werkzeugkiste, das du nutzen kannst, um ein großartiger Büchsenmacher zu sein!
37.9 EUR 5 37,90 € *
Lieferzeit ca. 14-21 Tage.
5 Stk. im Großlager
Eigenschaften: Art: Blank Breite: .125 Hersteller/Modell: 1911 Höhe: .275 Outline: None

Eigenschaften

Art: Blank Breite: .125 Hersteller/Modell: 1911 Höhe: .275 Outline: None Versandgewicht: 0,009kg Versandhöhe: 13mm Versandbreite: 76mm Versandlänge: 152mm

Artikeldetails

Made in USA



Ted Yost developed and made these sights several years ago and after a long absence from the marketplace they are once again available from Harrison Design. These sights can be used to rescue a slide from mis-cut front dovetails. They have an oversize dovetail base featuring nominal dimensions of .085"" depth, .375"" width with a 65 dovetail angle. That's big enough to rescue most any sort of ugliness and butchery. The blade is .275"" tall X .630"" long X .125 wide. The vertical rill pin has been omitted so you can match it's location to wherever your slide's hole location is located. The dovetail base is .625"" wide, so it can be blended to the top of your slide, or youcan cut the sides back for the appearance you want. A radius is machined at the point where the blade joins the dovetail base, strengthening the sight appreciably. This is a part that every gunsmith should keep 2 or 3 of on hand as it can get you out of a jam is a slip up is made. It can be cut down and made into other sight blanks as well. It's a great tool for your toolbox you use to be a great gunsmith!  
Newsletter