Extended Buttpad adds approximately ½" to the length of pull and provides extra protection from felt recoil for easier between-shot recovery during rapid fire. Deep horizontal ridges ensure a secure purchase on shoulder. Installs in minutes reusing the original pad’s mounting screws.
SPECS: Extended Buttpad - Molded rubber, black. .80" thick. Adds approximately ½" (1.6cm) to the length of pull over the stock’s original factory pad. 3.1 oz. (89g) weight. Fits the FAL and HK/G3 style stocks and not for the AR-15 or AR 308 PRS early stock.
Mehr...
Schnelle Feldanpassung
Das erweiterte Schaftkappe verlängert den Rückstoßabstand um etwa ½" und bietet zusätzlichen Schutz vor gefühltem Rückstoß für eine leichtere Erholung zwischen den Schüssen bei schnellem Feuer. Tiefe horizontale Rillen sorgen für einen sicheren Halt an der Schulter. Lässt sich in Minuten montieren, indem die ursprünglichen Befestigungsschrauben des Pads wiederverwendet werden.
SPECS: Erweitertes Schaftkappe - Geformtes Gummi, schwarz. 0,80" dick. Verlängert den Rückstoßabstand um etwa ½" (1,6 cm) gegenüber dem ursprünglichen Werkskappe des Schafts. Gewicht 3,1 oz. (89g). Passt auf FAL und HK/G3 Stil Schäfte und nicht für AR-15 oder AR 308 PRS frühe Schäfte.
Mehr...
Kundenbewertungen zu MAGPUL PRS2 verlängerte Schaftkappe
Anzahl der Bewertungen: 2
Von brownells.com: 2
Durchschnittliche Bewertung: 3
Only fits stock with two screw holes(26.12.2011)
There are many versions of a FN FAl or FNH mine is a Hesse and the butpad doesn't fit as it requires two screws holes to attach to the stock. If you have a single screw centered this product will not fit. If you have the two screw holes its a good product. Contact Brownell technical before you buy they are helpful
FOR PRS STOCK, NOT AN ACTUAL FAL STOCK.(31.10.2012)
Unlike the previous reveiwer, I used this as intented on a the MagPul PRS stock on the FAL. It works as advertised, but only on the PRS stock. It is not an FAL buttpad, its a PRS butt pad. Reading is fundamental.
Artikel-Nr.: 100005599 MAGPUL PRS2 verlängerte Schaftkappe Herstellerproduktnummer: MAG342-BLK873750000893 Das erweiterte Schaftkappe verlängert den Rückstoßabstand um etwa ½" und bietet zusätzlichen Schutz vor gefühltem Rückstoß für eine leichtere Erholung zwischen den Schüssen bei schnellem Feuer. Tiefe horizontale Rillen sorgen für einen sicheren Halt an der Schulter. Lässt sich in Minuten montieren, indem die ursprünglichen Befestigungsschrauben des Pads wiederverwendet werden.
Extended Buttpad adds approximately ½" to the length of pull and provides extra protection from felt recoil for easier between-shot recovery during rapid fire. Deep horizontal ridges ensure a secure purchase on shoulder. Installs in minutes reusing the original pad’s mounting screws.
SPECS: Extended Buttpad - Molded rubber, black. .80" thick. Adds approximately ½" (1.6cm) to the length of pull over the stock’s original factory pad. 3.1 oz. (89g) weight. Fits the FAL and HK/G3 style stocks and not for the AR-15 or AR 308 PRS early stock.
Mehr...
Schnelle Feldanpassung
Das erweiterte Schaftkappe verlängert den Rückstoßabstand um etwa ½" und bietet zusätzlichen Schutz vor gefühltem Rückstoß für eine leichtere Erholung zwischen den Schüssen bei schnellem Feuer. Tiefe horizontale Rillen sorgen für einen sicheren Halt an der Schulter. Lässt sich in Minuten montieren, indem die ursprünglichen Befestigungsschrauben des Pads wiederverwendet werden.
SPECS: Erweitertes Schaftkappe - Geformtes Gummi, schwarz. 0,80" dick. Verlängert den Rückstoßabstand um etwa ½" (1,6 cm) gegenüber dem ursprünglichen Werkskappe des Schafts. Gewicht 3,1 oz. (89g). Passt auf FAL und HK/G3 Stil Schäfte und nicht für AR-15 oder AR 308 PRS frühe Schäfte.
Mehr...
Kundenbewertungen zu MAGPUL PRS2 verlängerte Schaftkappe
Anzahl der Bewertungen: 2
Von brownells.com: 2
Durchschnittliche Bewertung: 3
Only fits stock with two screw holes(26.12.2011)
There are many versions of a FN FAl or FNH mine is a Hesse and the butpad doesn't fit as it requires two screws holes to attach to the stock. If you have a single screw centered this product will not fit. If you have the two screw holes its a good product. Contact Brownell technical before you buy they are helpful
FOR PRS STOCK, NOT AN ACTUAL FAL STOCK.(31.10.2012)
Unlike the previous reveiwer, I used this as intented on a the MagPul PRS stock on the FAL. It works as advertised, but only on the PRS stock. It is not an FAL buttpad, its a PRS butt pad. Reading is fundamental.