Eigenschaften
- Patrone:
Universal
- Versandgewicht: 0,113kg
- Versandhöhe: 41mm
- Versandbreite: 97mm
- Versandlänge: 155mm
- UPC: 090255704792
Artikeldetails
No Export, dieses Produkt ist nur in Deutschland erhältlich.
Nicht verfügbar.
Artikel-Nr.: 749004278
Herst.-Nr.: HK55
Benachrichtigt werden, sobald verfügbar? Hier klicken 42.9 EURDas erschwingliche LOCK-N-LOAD™ HEADSPACE GAUGE TOOL von HORNADY ist das ideale Werkzeug für jeden Handlader. Mit diesem Set kannst du die Veränderungen des Headspace deiner Patronen ganz einfach mit einem Dial- oder Digitalmaßstab messen.
Das Set enthält verschiedene Bushing-Größen, die je nach Patronenfamilie in den Hornady Lock-N-Load Comparator Body eingesetzt werden. Dieser wird an einem Maßstab befestigt, sodass du die Unterschiede zwischen abgefeuerten und bearbeiteten Hülsen genau messen kannst. So kannst du deine Größenwerkzeuge optimal anpassen, um eine perfekte Passform in deinem Kammer zu gewährleisten.
Wenn du deine Hülsen übermäßig vergrößerst, kann das zu Problemen mit dem Headspace führen, was unter anderem die Lebensdauer der Hülsen verkürzen kann. Das Hornady Lock-N-Load Headspace Gauge Set ermöglicht es dir, den Abstand vom Hülsenboden bis zur Datumslinie auf der Schulter der Hülse zu messen.
Schau dir auch das Hornady Gauge Bushing Chart an, um die passende Größe für deine Bedürfnisse zu finden!
Universal
Saves your brass 04.03.2016
I purchased these once I started loading the less common calibers (more specific 6.5 Grendel). When brass is .70/piece for decent brass, you want it to last a while. Since this was an auto loader, it's hard on brass. I was WAY oversizing my brass by putting it back to factory specs. I set the dies up according to manufacture recommendations, and it worked as it should. However, I noticed on the 3rd and 4th firings, the brass would start to harden (needed to be annealed) and when I full length sized them, it would leave a ring of brass around the base of the case. I knew this was killing my cases and my pocket book. I purchased this kit so I would bump the shoulders back (.003" per the recommended for auto loaders) and it works like a charm. I have been able to get 7 or 8 firings before the brass needs annealed because it's being worked so much less in the chamber. This also eliminates the need for a neck sizer as well. When shooting my bolt actions, I used to neck size as long as I could, but eventually, you have to size it back down because the shoulder expands enough to cause issues. When you use these, you can set up your FL sizer to bump the shoulder back .001" and it's very easy to chamber, and each case is the exact same, so no need to worry about variations in your load. I can't believe I waited as long as I did to purchase this tool. This should have been purchased at the beginning/learning stages of my reloading obsession and I would have been much better off!
Complete set for all calibers... 30.09.2015
A complete set of headspace gages (for setting headspace by gaging the shoulder datum on a bottleneck cartridge. It ships with an anvil that attaches to the jaw of your dial/digital caliper and I use the anvil with custom made gages for determining cartridge overall length (measured on the bullet ogive), the most accurate and repeatable method).
Absolutely necessary for determining the amount of 'bump back' to set your die at to attain easy bolt lift and no brass wipe on the bolt face.
Beim Laden dieses Inhalts ist ein Fehler aufgetreten. Bitte aktualisiere die Seite, um fortzufahren. Wenn das Problem weiterhin besteht, wende dich bitte an unseren Kundenservice.