Brownells Deutschland - Einer der größten Lieferanten für Waffenteile, Büchsenmacherwerkzeug & Schießsportzubehör Deutschland

EGW
WALTHER 22 VORTEX VIPER/VENOM SIGHT MOUNT

841370115709 296000654
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
76.9 76.9 1 EUR
Artikel-Nr.: 296000654
EGW WALTHER 1911-22 VORTEX VIPER/VENOM SIGHT MOUNT
Herstellerproduktnummer: 49302 841370115709 EGW Red-Dot-Visiere sollen von links nach rechts installiert werden (mit der Mündung nach vorne gerichtet). Die Schwalbenschwanzführung hat eine progressive Verjüngung, um die Installation zu erleichtern. Einfach das hintere Visier an deiner Waffe entfernen und durch die EGW Montage ersetzen, um dein Vortex Viper/Venom, Burris FastFire oder Docter Red-Dot-Visier zu montieren. Keine Änderungen sind erforderlich. Du kannst die Montage jederzeit abnehmen und dein hinteres Visier wieder anbringen. Befestigungsmaterial ist enthalten. Installationsanweisungen Entferne das hintere Visier* Installiere die EGW Visiermontage in der Schwalbenschwanzführung Ziehe die Madenschraube fest (falls zutreffend) Platziere das Red-Dot-Visier auf der EGW Visiermontage (das Platzieren eines kleinen Stücks Papier zwischen dem Red-Dot-Visier und der Visiermontage erleichtert die Entfernung und hält Loctite vom Red-Dot-Visier fern.) Trage blaues Loctite auf die mitgelieferten Befestigungsschrauben auf Ziehe die Befestigungsschrauben mit einem Drehmoment von 15in/lbs fest 2 Zylinderkopfschrauben - Für Vortex Viper und Venom Visiere mitgeliefert 2 Senkkopfschrauben - Für Burris FastFire und Docter Visiere mitgeliefert Die mit dieser Montage gelieferten Schrauben erfordern einen 5/64'' Inbusschlüssel für die Installation. Eine Modifikation deiner Waffe kann die Garantie des Herstellers ungültig machen. Dieses Produkt sollte von einem qualifizierten Büchsenmacher installiert und überprüft werden. Es wird keine Haftung für Schäden oder Verletzungen übernommen, die durch unsachgemäße Installation oder Verwendung dieses Produkts entstehen könnten.
76.9 EUR 4 76,90 € *
Lieferzeit ca. 14-21 Tage.
4 Stk. im Großlager
Eigenschaften: Art: Tactical Basenanzahl: 1-Piece Farbe: Black Hersteller/Modell: Walther Material: Aluminum Modell: P22

Eigenschaften

Art: Tactical Basenanzahl: 1-Piece Farbe: Black Hersteller/Modell: Walther Material: Aluminum Modell: P22 Versandgewicht: 0,045kg Versandhöhe: 25mm Versandbreite: 76mm Versandlänge: 140mm

Artikeldetails

Made in USA



EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
Newsletter