Brownells Deutschland - Einer der größten Lieferanten für Waffenteile, Büchsenmacherwerkzeug & Schießsportzubehör Deutschland

EGW
S&W M&P VORTEX VIPER/VENOM SIGHT MOUNT

841370113934 296000660
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This Mount does not fit: Smith & Wesson M&P C.O.R.E Series (Already optics ready) Smith & Wesson M&P Shield EZ .380 Smith & Wesson M&P .22 Compact Smith & Wesson SW9VE Smith & Wesson SW40VE
76.9 76.9 1 EUR
Artikel-Nr.: 296000660
EGW S&W M&P VORTEX VIPER/VENOM SIGHT MOUNT
Herstellerproduktnummer: 49308 841370113934 EGW Red-Dot-Visiere sollen von links nach rechts installiert werden (wobei die Mündung nach vorne zeigt). Die Schwalbenschwanzführung hat eine progressive Verjüngung, um die Installation zu erleichtern. Einfach das hintere Visier deiner Waffe entfernen und durch die EGW-Montage ersetzen, um dein Vortex Viper/Venom, Burris FastFire oder Docter Red-Dot-Visier zu montieren. Du kannst die Montage jederzeit abnehmen und dein hinteres Visier wieder anbringen. Montagematerial ist enthalten. Installationsanleitung Entferne das hintere Visier* Installiere die EGW-Montage in der Schwalbenschwanzführung Ziehe die Madenschraube fest (falls zutreffend) Platziere das Red-Dot-Visier auf der EGW-Montage (ein kleines Stück Papier zwischen Red-Dot-Visier und Montage zu legen, erleichtert die Demontage und hält Loctite von dem Red-Dot-Visier fern.) Trage blaues Loctite auf die mitgelieferten Montageschrauben auf Ziehe die Montageschrauben mit einem Drehmoment von 15in/lbs an 2 Zylinderkopfschrauben - Mitgeliefert für Vortex Viper und Venom Visiere 2 Senkkopfschrauben - Mitgeliefert für Burris FastFire und Docter Visiere Die mit dieser Montage gelieferten Schrauben erfordern einen 5/64'' Inbusschlüssel für die Installation. Eine Modifikation deiner Waffe kann die Garantie des Herstellers ungültig machen. Dieses Produkt sollte von einem qualifizierten Büchsenmacher installiert und überprüft werden. Es wird keine Haftung für Schäden oder Verletzungen übernommen, die durch unsachgemäße Installation oder Verwendung dieses Produkts entstehen können. Diese Montage passt nicht für: Smith & Wesson M&P C.O.R.E Series (bereits optikbereit) Smith & Wesson M&P Shield EZ .380 Smith & Wesson M&P .22 Compact Smith & Wesson SW9VE Smith & Wesson SW40VE
76.9 EUR 2 76,90 € *
Lieferzeit ca. 14-21 Tage.
2 Stk. im Großlager
Eigenschaften: Art: Tactical Basenanzahl: 1-Piece Farbe: Black Hersteller/Modell: Smith & Wesson Material: Aluminum Modell: M&P Shield, M&P Compact, M&P 2.0 Compact, SD9-VE

Eigenschaften

Art: Tactical Basenanzahl: 1-Piece Farbe: Black Hersteller/Modell: Smith & Wesson Material: Aluminum Modell: M&P Compact,M&P Shield,SD9-VE,M&P 2.0 Compact Versandgewicht: 0,045kg Versandhöhe: 25mm Versandbreite: 76mm Versandlänge: 140mm

Artikeldetails

Made in USA



EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This Mount does not fit: Smith & Wesson M&P C.O.R.E Series (Already optics ready) Smith & Wesson M&P Shield EZ .380 Smith & Wesson M&P .22 Compact Smith & Wesson SW9VE Smith & Wesson SW40VE
Newsletter