Brownells Deutschland - Einer der größten Lieferanten für Waffenteile, Büchsenmacherwerkzeug & Schießsportzubehör Deutschland

EGW
SIG SAUER P220-229, 320 VORTEX VIPER/VENOM SIGHT MOUNT

841370112920 296000665
This mount does not work on any optics ready Sigs. EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount does not fit: Sig 1911s Any Optics Ready Sigs i.e. P226 Legion RX, P229 RX, P320 X-Carry etc. P210 Target P365 (The dovetail cut is too deep to work with our mount) FN 509 Tactical
76.9 76.9 1 EUR
Artikel-Nr.: 296000665
EGW SIG SAUER P220-229, 320 VORTEX VIPER/VENOM SIGHT MOUNT
Herstellerproduktnummer: 49318 841370112920 Diese Montage funktioniert nicht bei allen Optics Ready Sigs. EGW Red-Dot-Visiere sollen von links nach rechts installiert werden (mit dem Lauf nach vorne zeigend). Die Schwanzschraube hat eine progressive Verjüngung, um die Installation zu erleichtern. Einfach das hintere Visier deiner Waffe entfernen und durch die EGW Montage ersetzen, um dein Vortex Viper/Venom, Burris FastFire oder Docter Red-Dot-Visier zu montieren. Du kannst die Montage jederzeit abnehmen und dein hinteres Visier wieder anbringen. Montagematerial ist enthalten. Installationsanweisungen: Entferne das hintere Visier* Installiere die EGW Montage in der Schwanzschraube Ziehe die Stellschraube fest (falls zutreffend) Platziere das Red-Dot-Visier auf der EGW Montage (ein kleines Stück Papier zwischen Red-Dot-Visier und Montage erleichtert die Demontage und hält Loctite vom Red-Dot-Visier fern.) Trage blaues Loctite auf die mitgelieferten Montageschrauben auf Ziehe die Montageschrauben mit 15in/lbs an 2 Button Head Cap Screws - Für Vortex Viper und Venom Visiere bereitgestellt 2 Flat Head Cap Screws - Für Burris FastFire und Docter Visiere bereitgestellt Die mit dieser Montage gelieferten Schrauben benötigen einen 5/64'' Innensechskantschlüssel zur Installation. Änderungen an deiner Waffe können die Garantie des Herstellers aufheben. Dieses Produkt sollte von einem qualifizierten Büchsenmacher installiert und überprüft werden. Für Schäden oder Verletzungen, die durch unsachgemäße Installation oder Verwendung dieses Produkts entstehen könnten, wird keine Haftung übernommen. Diese Montage passt nicht für: Sig 1911s Alle Optics Ready Sigs, z.B. P226 Legion RX, P229 RX, P320 X-Carry usw. P210 Target P365 (Der Schwanzschraubenschnitt ist zu tief für unsere Montage) FN 509 Tactical
76.9 EUR 2 76,90 € *
Lieferzeit ca. 14-21 Tage.
2 Stk. im Großlager
Eigenschaften: Art: Tactical Basenanzahl: 1-Piece Farbe: Black Hersteller/Modell: Sig Sauer, FN, Bersa Material: Aluminum Modell: P238, P226, P229, P220, P938, P320, P225, P228, P224, P245, P227, P239, SP2022, 509, P210A, Thunder UC, Thunder HC, M11-A1, MK25

Eigenschaften

Art: Tactical Basenanzahl: 1-Piece Farbe: Black Hersteller/Modell: FN,Sig Sauer,Bersa Material: Aluminum Modell: P210A,P220,Thunder HC,P226,P227,P938,M11-A1,SP2022,P225,P239,Thunder UC,P229,P320,P224,509,P245,MK25,P228,P238 Versandgewicht: 0,045kg Versandhöhe: 25mm Versandbreite: 76mm Versandlänge: 140mm

Artikeldetails

Made in USA



This mount does not work on any optics ready Sigs. EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount does not fit: Sig 1911s Any Optics Ready Sigs i.e. P226 Legion RX, P229 RX, P320 X-Carry etc. P210 Target P365 (The dovetail cut is too deep to work with our mount) FN 509 Tactical
Newsletter