Brownells Deutschland - Einer der größten Lieferanten für Waffenteile, Büchsenmacherwerkzeug & Schießsportzubehör Deutschland

EGW
SIG SAUER P220 10MM HUNTER VORTEX VIPER/VENOM SIGHT MOUNT

841370115983 296000674
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
76.9 76.9 1 EUR
Artikel-Nr.: 296000674
EGW SIG SAUER P220 10MM HUNTER VORTEX VIPER/VENOM SIGHT MOUNT
Herstellerproduktnummer: 49328 841370115983 EGW Red-Dot-Visiere sollen von links nach rechts installiert werden (mit dem Lauf nach vorne gerichtet). Die Schwalbenschwanzführung hat eine progressive Verjüngung, um eine einfachere Installation zu ermöglichen. Entferne einfach das hintere Visier deiner Waffe und ersetze es durch die EGW-Montage, um dein Vortex Viper/Venom, Burris FastFire oder Docter Red-Dot-Visier zu montieren. Du kannst die Montage jederzeit abnehmen und dein hinteres Visier wieder anbringen. Montagematerial ist enthalten. Installationsanweisungen Entferne das hintere Visier* Installiere die EGW-Montage in der Schwalbenschwanzführung Ziehe die Feststellschraube an (falls zutreffend) Platziere das Red-Dot-Visier auf der EGW-Montage (ein kleines Stück Papier zwischen Red-Dot-Visier und Montage zu legen, erleichtert die Entfernung und hält Loctite vom Red-Dot-Visier fern.) Trage blaues Loctite auf die mitgelieferten Montageschrauben auf Ziehe die Montageschrauben mit einem Drehmoment von 15in/lbs an 2 Zylinderkopfschrauben - mitgeliefert für Vortex Viper und Venom Visiere 2 Senkkopfschrauben - mitgeliefert für Burris FastFire und Docter Visiere Die mit dieser Montage gelieferten Schrauben benötigen einen 5/64'' Inbusschlüssel zur Installation. Eine Modifikation deiner Feuerwaffe kann die Garantie des Herstellers aufheben. Dieses Produkt sollte von einem qualifizierten Büchsenmacher installiert und überprüft werden. Es wird keine Haftung für Schäden oder Verletzungen übernommen, die durch unsachgemäße Installation oder Verwendung dieses Produkts entstehen könnten.
76.9 EUR 0 76,90 € *
Benachrichtigt werden, sobald verfügbar? Hier klicken
Nicht auf Lager. Kein Liefertermin bekannt.
Eigenschaften: Art: Tactical Basenanzahl: 1-Piece Farbe: Black Hersteller/Modell: Sig Sauer Material: Aluminum Modell: P220 Super Match SAO, P220 10mm Hunter

Eigenschaften

Art: Tactical Basenanzahl: 1-Piece Farbe: Black Hersteller/Modell: Sig Sauer Material: Aluminum Modell: P220 Super Match SAO,P220 10mm Hunter Versandgewicht: 0,045kg Versandhöhe: 25mm Versandbreite: 76mm Versandlänge: 140mm

Artikeldetails

Made in USA



EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
Newsletter