EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount will not work with FN FNP or FN 5.7.
Die perfekte Lösung für deine Vortex Viper/Venom Montage!
Der FN FNS, FNX VORTEX VIPER/VENOM SIGHT MOUNT von EGW ist die ideale Wahl, um dein Vortex Viper oder Venom sicher und stabil zu montieren. Dieser Montagesatz ist speziell für die FN/FNS/FNX Modelle konzipiert und bietet eine einfache Installation.
Produktbeschreibung
Die EGW Rotpunktvisiere sind so konzipiert, dass sie von links nach rechts installiert werden (mit dem Mündungsende nach vorne). Der Dovetail hat eine progressive Taper, die die Installation erleichtert. Entferne einfach das hintere Visier deiner Waffe und ersetze es durch die EGW Montage, um dein Vortex Viper/Venom, Burris FastFire oder Docter Rotpunktvisier zu montieren. Du kannst die Montage jederzeit abnehmen und dein hinteres Visier wieder anbringen.
Installationsanleitung
- Entferne das hintere Visier*
- Installiere die EGW Sight Mount im Dovetail
- Ziehe die Set-Schraube fest (falls zutreffend)
- Platziere das Rotpunktvisier auf der EGW Sight Mount (ein kleines Stück Papier zwischen dem Rotpunktvisier und der Montage erleichtert die Entfernung und hält Loctite vom Rotpunktvisier fern).
- Trage blauen Loctite auf die mitgelieferten Montageschrauben auf
- Ziehe die Montageschrauben auf 15in/lbs
Enthaltene Schrauben:
- 2 Button Head Cap Screws - Für Vortex Viper und Venom Sights
- 2 Flat Head Cap Screws - Für Burris FastFire und Docter Sights
Die mit diesem Montagesatz gelieferten Schrauben erfordern einen 5/64'' Innensechskantschlüssel zur Installation.
Hinweis: Änderungen an deiner Feuerwaffe können die Herstellergarantie ungültig machen. Dieses Produkt sollte von einem qualifizierten Büchsenmacher installiert und überprüft werden. Es wird keine Haftung für Schäden oder Verletzungen übernommen, die aus unsachgemäßer Installation oder Verwendung dieses Produkts resultieren. Diese Montage funktioniert nicht mit FN FNP oder FN 5.7.