Ihr Warenkorb ist leer.

Warenkorb

RCBS
BULLET PULLER W/O COLLET

076683094407 749003249

This collet type bullet puller from RCBS will pull jacketed bullets from .17 caliber through50 caliber with the appropriate collet (order collets separately from chart) installed in the puller body. Puller can be used in any 7/8-14single stage reloading press. RCBS states that the collets do not damage jacketed bullets. Not for rimfire ammunition. Requires separate purchase of caliber specific collets.

Mehr...

Dieser Collet-Typ Geschosszieher von RCBS kann Mantelgeschosse von .17 bis .50 Kaliber mit dem entsprechenden, separat erhältlichen Collet (siehe Tabelle) aus dem Zieherkörper entfernen. Der Zieher kann in jeder 7/8-14 Einzelstation-Presse verwendet werden. RCBS gibt an, dass die Collets die Mantelgeschosse nicht beschädigen. Nicht für Randfeuermunition geeignet. Erfordert den separaten Kauf von kaliberspezifischen Collets.

Mehr...

Kundenbewertungen zu RCBS Bullet Puller w/o Collet

Anzahl der Bewertungen: 8
Von brownells.com: 7
Durchschnittliche Bewertung: 4,9

Absolut empfehlungswert ! (08.10.2020)

Ich benutze diesen RCBS Bullet Puller auf einer Forster Single Stage Presse für die Kaliber 9mm und .308 Winchester.
Damit der Hebel nicht an den Arm der Presse anstößt, habe ich diesen vorsichtig mit einem Hammer gelöst sodass er sich jetzt horizontal verschieben und sogar entfernen lässt. Die Geschosse lassen sich ohne den kleinsten Makel entfernen.

VITAL RELOADING DYE (12.10.2013)

I have a kinetic bullet puller but this is vital for the reloader who wants his loads just right.

I could have used this to adapt more loads than I've shot.

There is no way you can be as efficient w/a kinetic puller.

RCBS Collet-style Bullet Puller (20.09.2014)

This is an easy tool to setup and use. It pulls bullets easily, as long as it can get a grip on them. Unfortunately, there are bullet designs that this won't pull, as I quickly discovered.

The bullets you intend to pull MUST have some of the exposed projectile to have the caliber diameter. I ran across some .40 S&W semi-wad cutters that have a reduced diameter truncated cone design that was too small for the collet to grip and the bullet shoulder was seated flush with the case mouth. As is it, I'll have to use an inertia puller, as tedious at that is.

On bullets that can be gripped by the collets, the bullet pulling task is fast and easy. Instructions were clear and precise enough that even a politician could use it.

As it came out of the box, and for the bullets I have tried it on so far, I can only give it 4 stars. Still, it's a puller you should have on your bench.

Very effective tool (14.01.2015)

When needing to pull a lot of bullets w/o damage, this is a very nice tool to have. Wish I had bought one 30 years ago (if they had them). Safer than the hammer method also.

Don't Delay This Purchase (04.04.2015)

I used my fathers old 1970 hammer puller for years only because it was all I knew. On a whim I spent the money on this puller and my only complaint was how mad I was that I waited 6 years to get it. It works like a charm, does not damage bullets like the mentioned 1970 hammer. Before I had this in my life I would dread the thought of pulling bullets from some test loads if they didnt shoot good. Now, I can crank out pulls in Seconds.

Threw the plastic hammer away! (15.11.2015)

As others have said, I also dreaded pulling bullets with the hammer style kinetic puller. And I do alot of reloading late at night. So the noise was a stopping point. I kinda thought this was gimmicky reading descriptions but I jumped in. Got the collets for .45, 22, and 30. Very impressed! So much quicker, no bullet damage. And powder stays in the case neatly. It even pulled some bullets that were seated way to deep and it pulled em. Using copper plated bullets in 45 this did not even expose lead. I actually have a new test with the help of this to check crimp neck tension. Set my crimp and pull bullet measure to make sure there is no swaging or damage. Love these tools that really help more tedious processes of reloading.

Works Great (29.02.2016)

I love this puller. It works great, prevents damage, and won't break off after smacking it. I broke 3 different inertia pullers and spent the money on this. The one complaint I have is the collet I have, 30 cal, is really tight and you have to hold down the top and force the bullet in. Once it's in, cranked down, it won't go anywhere. The other bad side is you cannot remove the bullet without pliers or sticking back inside the case a tad, then removing it by hand. You can slip it over the ogive and crank it down, and that will work, but anything crimped, or with tight neck tension, it won't work that way as it will slide off. However, the perk to his is that I am able to pull 7mm (.284), 270 (.277), 6.5 (.264) bullets with this same collet after cranking it down all the way. I can't complain about that as other that .22 cal, I don't have many other calibers! I would definitely buy again, but I would try to loosen up the tension a little bit if possible.

Great Value (17.04.2018)

The RCBS bullet puller is a good solution to pulling bullets using your existing single stage press. It is well made with a decent finish and solid steel parts. The collets are well made and have a decent amount of steel after the slits to give them good heft and durability.

Lesen Sie 7 weitere Bewertungen bei brownells.com

43.9 43.9 1 EUR

Artikel-Nr.: 749003249
RCBS Bullet Puller w/o Collet
Herstellerproduktnummer: 9440 076683094407 Dieser Collet-Typ Geschosszieher von RCBS kann Mantelgeschosse von .17 bis .50 Kaliber mit dem entsprechenden, separat erhältlichen Collet (siehe Tabelle) aus dem Zieherkörper entfernen. Der Zieher kann in jeder 7/8-14 Einzelstation-Presse verwendet werden. RCBS gibt an, dass die Collets die Mantelgeschosse nicht beschädigen. Nicht für Randfeuermunition geeignet. Erfordert den separaten Kauf von kaliberspezifischen Collets.

43.9 EUR 0 43,90 € *

Nachbestellt, Lieferzeit ca. 4-12 Wochen aus dem Großlager.

Eigenschaften: Kaliber: Universal

Auf die Wunschliste setzen

Frage stellen

Details

Auf die Wunschliste setzen

Frage stellen

Eigenschaften

Kaliber: Universal Versandgewicht: 0,635kg Versandhöhe: 43mm Versandbreite: 114mm Versandlänge: 150mm

Artikeldetails

Made in USA

Mehr...

Kundenbewertungen zu RCBS Bullet Puller w/o Collet

Anzahl der Bewertungen: 8
Von brownells.com: 7
Durchschnittliche Bewertung: 4,9

Absolut empfehlungswert ! (08.10.2020)

VITAL RELOADING DYE (12.10.2013)

RCBS Collet-style Bullet Puller (20.09.2014)

Very effective tool (14.01.2015)

When needing to pull a lot of bullets w/o damage, this is a very nice tool to have. Wish I had bought one 30 years ago (if they had them). Safer than the hammer method also.

Don't Delay This Purchase (04.04.2015)

Threw the plastic hammer away! (15.11.2015)

Works Great (29.02.2016)

Great Value (17.04.2018)

Lesen Sie 7 weitere Bewertungen bei brownells.com

Kunden kauften auch

RCBS 25 Caliber Bullet Puller Collet
RCBS BULLET PULLER COLLET

RCBS

Auf Lager

23,90 € * 22,90 € - 24,90 €*

Geschosszieher

RCBS Shellholder #47
RCBS SHELLHOLDERS

RCBS

Bestellbar, nicht vorrätig

19,90 € * 8,00 € - 21,90 €*

Hülsenhalter & Hülsenhalterplatten

HORNADY 45-70 Government Modified Case
HORNADY LOCK-N-LOAD MODIFIED CASES

HORNADY

Bestellbar, nicht vorrätig

11,90 € * 9,90 € - 41,90 €*

Werkzeug zur Bestimmung der Geschosssetztiefe | Hülsenlehren & Verschlussabstandslehren

L.E. WILSON, INC. 257 Weatherby Magnum FIRED Case Holder
L.E. WILSON, INC. RIFLE CASE HOLDERS

L.E. WILSON

Auf Lager

20,90 € * 20,90 € - 29,90 €*

Hülsenhalter für Trimmer | Hülsentrimmer

3,8

LEE PRECISION Lee Quick Trim Die, 308 Win
LEE PRECISION QUICK TRIM DIES

LEE PRECISION

Bestellbar, nicht vorrätig

20,90 € * 20,90 € - 22,90 €*

Hülsenhalter für Trimmer | Hülsentrimmer

Anmeldung

Kennwort vergessen?
Registrieren

Links

Produktkategorien

Kontakt

Kontaktformular
+49(0)4321 / 5562358 Mo.-Fr. 09-12 und 14-15 Uhr
Händler werden?
Karriere

Bestellen

Kundenservice

Unser Versprechen:

Ob Sportschütze, Jäger, Büchsenmacher, Militär oder Polizist, Waffen-Tüflter oder Enthusiast - bei uns bist du richtig! Keine Extrakosten für den Zoll, keine Probleme mit Importgenehmigungen und kein Mindestbestellwert.
Seit über 75 Jahren vertrauen unsere Kunden den qualitativ hochwertigen Waffen, Waffenteilen und dem Zubehör von Brownells. Bei uns findest du mehr als 50.000 Artikel, darunter einzigartige Waffenteile, Zubehör, Büchsenmacher-Werkzeuge, Munition und andere Produkte zur Wartung, Instandsetzung und Tuning deiner Waffen.