Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.780" Overall Width: 1.1" Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw Red Dot Fitment: Trijicon RMR, Holosun HS507C This mounts fits: Baby Desert Eagle (Post 2006) EAA Witness Elite Match This mount does not fit: Rock Island 1911s Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Flat Head Cap Screws - Provided for Trijicon RMR The screws that are included with this mount require a 5/64'' allen wrench for installation.
Mehr...
Material: 7075 Aluminium Beschichtung: Mattschwarz Hardcoat Gesamtlänge: 1,780" Gesamtbreite: 1,1" Montagematerial: (2) 6-32 Flachkopfschrauben, (1) 6-32 X 3/16 Gewindestift Red Dot Passform: Trijicon RMR, Holosun HS507C Diese Montage passt für: Baby Desert Eagle (nach 2006) EAA Witness Elite Match Diese Montage passt nicht für: Rock Island 1911s Einfach das hintere Visier deiner Waffe entfernen und durch unsere Montage ersetzen, um dein Trijicon RMR Red Dot Visier zu montieren. Keine Änderungen erforderlich. Unsere Montage kann jederzeit entfernt und das hintere Visier wieder angebracht werden. Montagematerial inklusive. Installationsanleitung Entferne das hintere Visier* Installiere die EGW Visiermontage im Schwalbenschwanz Ziehe die Gewindestiftschraube fest (falls zutreffend) Platziere das Red Dot Visier auf der EGW Visiermontage (ein kleines Stück Papier zwischen Red Dot Visier und Visiermontage erleichtert die Demontage und hält Loctite vom Red Dot Visier fern.) Trage blaues Loctite auf die mitgelieferten Montageschrauben auf Ziehe die Montageschrauben mit einem Drehmoment von 15in/lbs fest 2 Flachkopfschrauben - für Trijicon RMR mitgeliefert Die Schrauben, die mit dieser Montage geliefert werden, benötigen einen 5/64'' Inbusschlüssel für die Installation.
Mehr...
76.976.91EUR
Artikel-Nr.: 296000571 EGW Bomar Trijicon RMR Sight Mount Herstellerproduktnummer: 49512841370116775 Material: 7075 Aluminium Beschichtung: Mattschwarz Hardcoat Gesamtlänge: 1,780" Gesamtbreite: 1,1" Montagematerial: (2) 6-32 Flachkopfschrauben, (1) 6-32 X 3/16 Gewindestift Red Dot Passform: Trijicon RMR, Holosun HS507C Diese Montage passt für: Baby Desert Eagle (nach 2006) EAA Witness Elite Match Diese Montage passt nicht für: Rock Island 1911s Einfach das hintere Visier deiner Waffe entfernen und durch unsere Montage ersetzen, um dein Trijicon RMR Red Dot Visier zu montieren. Keine Änderungen erforderlich. Unsere Montage kann jederzeit entfernt und das hintere Visier wieder angebracht werden. Montagematerial inklusive. Installationsanleitung Entferne das hintere Visier* Installiere die EGW Visiermontage im Schwalbenschwanz Ziehe die Gewindestiftschraube fest (falls zutreffend) Platziere das Red Dot Visier auf der EGW Visiermontage (ein kleines Stück Papier zwischen Red Dot Visier und Visiermontage erleichtert die Demontage und hält Loctite vom Red Dot Visier fern.) Trage blaues Loctite auf die mitgelieferten Montageschrauben auf Ziehe die Montageschrauben mit einem Drehmoment von 15in/lbs fest 2 Flachkopfschrauben - für Trijicon RMR mitgeliefert Die Schrauben, die mit dieser Montage geliefert werden, benötigen einen 5/64'' Inbusschlüssel für die Installation.
Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.780" Overall Width: 1.1" Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw Red Dot Fitment: Trijicon RMR, Holosun HS507C This mounts fits: Baby Desert Eagle (Post 2006) EAA Witness Elite Match This mount does not fit: Rock Island 1911s Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Flat Head Cap Screws - Provided for Trijicon RMR The screws that are included with this mount require a 5/64'' allen wrench for installation.
Mehr...
Material: 7075 Aluminium Beschichtung: Mattschwarz Hardcoat Gesamtlänge: 1,780" Gesamtbreite: 1,1" Montagematerial: (2) 6-32 Flachkopfschrauben, (1) 6-32 X 3/16 Gewindestift Red Dot Passform: Trijicon RMR, Holosun HS507C Diese Montage passt für: Baby Desert Eagle (nach 2006) EAA Witness Elite Match Diese Montage passt nicht für: Rock Island 1911s Einfach das hintere Visier deiner Waffe entfernen und durch unsere Montage ersetzen, um dein Trijicon RMR Red Dot Visier zu montieren. Keine Änderungen erforderlich. Unsere Montage kann jederzeit entfernt und das hintere Visier wieder angebracht werden. Montagematerial inklusive. Installationsanleitung Entferne das hintere Visier* Installiere die EGW Visiermontage im Schwalbenschwanz Ziehe die Gewindestiftschraube fest (falls zutreffend) Platziere das Red Dot Visier auf der EGW Visiermontage (ein kleines Stück Papier zwischen Red Dot Visier und Visiermontage erleichtert die Demontage und hält Loctite vom Red Dot Visier fern.) Trage blaues Loctite auf die mitgelieferten Montageschrauben auf Ziehe die Montageschrauben mit einem Drehmoment von 15in/lbs fest 2 Flachkopfschrauben - für Trijicon RMR mitgeliefert Die Schrauben, die mit dieser Montage geliefert werden, benötigen einen 5/64'' Inbusschlüssel für die Installation.