Brownells Deutschland - Einer der größten Lieferanten für Waffenteile, Büchsenmacherwerkzeug & Schießsportzubehör Deutschland

AMERICAN TRIGGER CORPORATION
AR-15 AR GOLD TRIGGER CURVED

100004262
Drop-In Fire Control System Gives A Light, Safe, Match-Grade Pull
Self-contained trigger/assembly installs in minutes and delivers a light, smooth, match-grade trigger pull free of grittiness, with an ultra-crisp letoff and short reset. Simply remove factory trigger and safety selector, drop in the module, reinstall selector and pins, and you’re ready to shoot. Completely new engagement geometry produces a light 3-lb. pull and crisp release without compromising reliability or safety. The two-stage design is adjustable for sear engagement, with a first-stage takeup of approximately 6 ounces, followed by actual sear movement taking up the rest of the weight—the reverse of the military two-stage AR trigger pull profile. Instead, the shooter can build force steadily, maintaining precise control and keeping his attention on the target. After release, reset travel is only .030", less than half the .070" typical of standard match triggers, to aid in fast, accurate follow-up shots. The sear captures the hammer at the back instead of near the pivot point to help produce the light pull and maintain safety. A second, independent, intercepting sear is positioned to block the hammer if it slips off the primary sear, as when the weapon is dropped or suffers hard impact. If the intercepting sear captures the hammer, pulling the trigger will still fire the rifle, though with a heavier pull weight. In addition, the Gold system uses the rifle’s factory safety to positively capture the hammer, like an M1 Garand, and roll it back below the primary sear for an extra margin of safety. A lightweight aluminum housing contains the entire system and maintains the correct tolerances between the working parts. The receiver pins serve only to anchor the module in the receiver, with no effect on trigger function.

SPECS: Trigger/Hammer – Wire EDM cut S7 tool steel. Housing – Aluminum, anodized, black. AR Gold fits any mil-spec AR-15 with .154" trigger and hammer pin holes. Will not fit rifles with Colt-type sear block or AR-style .308 rifles.

399.9 399.9 1 EUR
Artikel-Nr.: 100004262
AMERICAN TRIGGER CORPORATION AR Gold Curved Trigger Adjustible
Herstellerproduktnummer: NONE Dieses selbstständige Abzugssystem lässt sich in Minuten installieren und liefert einen leichten, geschmeidigen, match-grade Abzugswiderstand ohne Rauheit, mit einem ultra-präzisen Abzug und kurzer Rückstellung. Einfach den Werksabzug und den Sicherungsselektor entfernen, das Modul einsetzen, Selektor und Stifte wieder einbauen und du bist bereit zum Schießen. Eine völlig neue Eingriffsgeometrie erzeugt einen leichten 3-lb. Widerstand und präzise Auslösung ohne die Zuverlässigkeit oder Sicherheit zu beeinträchtigen. Das zweistufige Design ist einstellbar für Sear-Eingriff, mit einer ersten Stufe von ungefähr 6 Unzen, gefolgt von der eigentlichen Sear-Bewegung, die den Rest des Gewichts aufnimmt – das Gegenteil des militärischen zweistufigen AR-Abzugswiderstandsprofils. Stattdessen kann der Schütze die Kraft stetig aufbauen, die präzise Kontrolle behalten und seine Aufmerksamkeit auf das Ziel richten. Nach der Auslösung beträgt der Rückstellweg nur .030", weniger als die Hälfte der typischen .070" von Standard-Match-Abzügen, um schnelle, präzise Folgeschüsse zu unterstützen. Der Sear fängt den Hammer hinten statt in der Nähe des Drehpunkts, um den leichten Zug zu unterstützen und die Sicherheit zu erhöhen. Ein zweiter, unabhängiger, abfangender Sear ist positioniert, um den Hammer zu blockieren, falls er vom primären Sear abrutscht, wie beim Fallenlassen der Waffe oder bei starkem Aufprall. Wenn der abfangende Sear den Hammer fängt, wird das Gewehr durch Betätigen des Abzugs immer noch feuern, allerdings mit einem schwereren Abzugsgewicht. Darüber hinaus nutzt das Gold-System die werkseitige Sicherung des Gewehrs, um den Hammer wie bei einem M1 Garand zu fangen und unterhalb des primären Sears für einen zusätzlichen Sicherheitsabstand zurückzurollen. Ein leichtes Aluminiumgehäuse enthält das gesamte System und hält die korrekten Toleranzen zwischen den arbeitenden Teilen. Die Empfängerstifte dienen nur dazu, das Modul im Empfänger zu verankern, ohne die Abzugsfunktion zu beeinflussen.
399.9 EUR 4 399,90 € *
Lieferzeit ca. 14-21 Tage.
4 Stk. im Großlager
Eigenschaften: Art: Drop-In Hersteller/Modell: AR-15

Eigenschaften

Art: Drop-In Hersteller/Modell: AR-15 Versandgewicht: 0,181kg Versandhöhe: 58mm Versandbreite: 114mm Versandlänge: 180mm

Artikeldetails

Made in USA
US-Exportklassifizierung: 0A501.c



Drop-In Fire Control System Gives A Light, Safe, Match-Grade Pull
Self-contained trigger/assembly installs in minutes and delivers a light, smooth, match-grade trigger pull free of grittiness, with an ultra-crisp letoff and short reset. Simply remove factory trigger and safety selector, drop in the module, reinstall selector and pins, and you’re ready to shoot. Completely new engagement geometry produces a light 3-lb. pull and crisp release without compromising reliability or safety. The two-stage design is adjustable for sear engagement, with a first-stage takeup of approximately 6 ounces, followed by actual sear movement taking up the rest of the weight—the reverse of the military two-stage AR trigger pull profile. Instead, the shooter can build force steadily, maintaining precise control and keeping his attention on the target. After release, reset travel is only .030", less than half the .070" typical of standard match triggers, to aid in fast, accurate follow-up shots. The sear captures the hammer at the back instead of near the pivot point to help produce the light pull and maintain safety. A second, independent, intercepting sear is positioned to block the hammer if it slips off the primary sear, as when the weapon is dropped or suffers hard impact. If the intercepting sear captures the hammer, pulling the trigger will still fire the rifle, though with a heavier pull weight. In addition, the Gold system uses the rifle’s factory safety to positively capture the hammer, like an M1 Garand, and roll it back below the primary sear for an extra margin of safety. A lightweight aluminum housing contains the entire system and maintains the correct tolerances between the working parts. The receiver pins serve only to anchor the module in the receiver, with no effect on trigger function.

SPECS: Trigger/Hammer – Wire EDM cut S7 tool steel. Housing – Aluminum, anodized, black. AR Gold fits any mil-spec AR-15 with .154" trigger and hammer pin holes. Will not fit rifles with Colt-type sear block or AR-style .308 rifles.

Newsletter