Lightweight, quick-detach mount lets you install and remove your Aimpoint Micro series red dot in seconds. Replaces original factory base and secures to the Aimpoint sight with four, high-strength, steel Torx® screws for a tight hold under heavy recoil. Mounts T-1 red dot at lowest height.
SPECS: 6061 T6 aluminum, hardcoat T3 mil-spec anodized, matte black. Height measured from top of rail to bottom of scope body - .31” (7.8mm). Fits Aimpoint Micro series red dot sights only.
Mehr...
Felsenfeste Montage
Leichte, schnell abnehmbare Montage, mit der du dein Aimpoint Micro Serie Rotpunktvisier in Sekunden anbringen und entfernen kannst. Ersetzt die originale Werkshalterung und wird mit vier hochfesten Stahl Torx® Schrauben am Aimpoint Visier befestigt, um auch bei starkem Rückstoß einen festen Halt zu gewährleisten. Montiert das T-1 Rotpunktvisier in der niedrigsten Höhe.
SPECS: 6061 T6 Aluminium, hartbeschichtet T3 mil-spec eloxiert, matt schwarz. Höhe gemessen von der Oberkante der Schiene bis zum unteren Rand des Zielfernrohrkörpers - .31” (7,8mm). Passt nur auf Aimpoint Micro Serie Rotpunktvisiere.
Mehr...
Kundenbewertungen zu AMERICAN DEFENSE MANUFACTURING Aimpoint Micro CAS-V Mounts, Standard Latch
Anzahl der Bewertungen: 4
Von brownells.com: 4
Durchschnittliche Bewertung: 4,5
works great with Sig Romeo5(05.11.2017)
Works well in conjunction with a fixed front sight post and allows a less obstructed view. Is secure and comes off quickly and does not add much weight. About 7.5 oz for the sight and base.
Great mount(09.01.2016)
I purchased this for my Aimpoint H1 and I am more than pleased with it. Sturdy mount, easy to install, and takes a beating in training. Highly recommend.
solid mount(30.08.2011)
I've used a couple of these mounts, the AD-T1-10 provides an absolute cowitness with flattop AR's. Overall I'm happy with these, they are solid and lock up tight, a good value for the money. This particular model is the low model for using on shotguns, pistols, etc. [...] I was going to go with a larue, but the I beam design they use on their absolute cowitness model looks flimsy to me.
mounted on AK(21.11.2015)
I used this to mount an Aimpoint T1 on my Maadi AK. When attached to the Ultimak gas tube I cannot see the enough of the iron sights to use them effectively - my reason for 4 stars. Otherwise, the mount is sturdy, easy to remove and it's American made.
Artikel-Nr.: 000004423 AMERICAN DEFENSE MANUFACTURING Aimpoint Micro CAS-V Mounts, Standard Latch Herstellerproduktnummer: ADT1CASVSTD818503010408 Leichte, schnell abnehmbare Montage, mit der du dein Aimpoint Micro Serie Rotpunktvisier in Sekunden anbringen und entfernen kannst. Ersetzt die originale Werkshalterung und wird mit vier hochfesten Stahl Torx® Schrauben am Aimpoint Visier befestigt, um auch bei starkem Rückstoß einen festen Halt zu gewährleisten. Montiert das T-1 Rotpunktvisier in der niedrigsten Höhe.
175.9EUR8175,90 €
*
Lieferzeit ca. 14-21 Tage. 8 Stk. im Großlager
Eigenschaften:Farbe: Matte BlackFits / Used For: Aimpoint Micro
Farbe:
Matte Black
Fits / Used For:
Aimpoint Micro
Versandgewicht: 0,113kgVersandhöhe: 53mmVersandbreite: 57mmVersandlänge: 121mm
Artikeldetails
Made in USA
Artikel-Nr.: 100004024 AMERICAN DEFENSE MANUFACTURING Aimpoint Micro Low QD Mount Herstellerproduktnummer: ADT1LSTD818503010385 Leichte, schnell abnehmbare Montage, mit der du dein Aimpoint Micro Serie Rotpunktvisier in Sekunden anbringen und entfernen kannst. Ersetzt die originale Werkshalterung und wird mit vier hochfesten Stahl Torx® Schrauben am Aimpoint Visier befestigt, um auch bei starkem Rückstoß einen festen Halt zu gewährleisten. Montiert das T-1 Rotpunktvisier in der niedrigsten Höhe.
Artikel-Nr.: 100017113 AMERICAN DEFENSE MANUFACTURING Aimpoint Micro Absolute Co-Witness Mount Herstellerproduktnummer: ADT110STD818503010422 Leichte, schnell abnehmbare Montage, mit der du dein Aimpoint Micro Serie Rotpunktvisier in Sekunden anbringen und entfernen kannst. Ersetzt die originale Werkshalterung und wird mit vier hochfesten Stahl Torx® Schrauben am Aimpoint Visier befestigt, um auch bei starkem Rückstoß einen festen Halt zu gewährleisten. Montiert das T-1 Rotpunktvisier in der niedrigsten Höhe.
Artikel-Nr.: 100017114 AMERICAN DEFENSE MANUFACTURING Aimpoint Micro Lower 1/3 Co-Witness Mount Herstellerproduktnummer: ADT111STD818503011184 Leichte, schnell abnehmbare Montage, mit der du dein Aimpoint Micro Serie Rotpunktvisier in Sekunden anbringen und entfernen kannst. Ersetzt die originale Werkshalterung und wird mit vier hochfesten Stahl Torx® Schrauben am Aimpoint Visier befestigt, um auch bei starkem Rückstoß einen festen Halt zu gewährleisten. Montiert das T-1 Rotpunktvisier in der niedrigsten Höhe.
Lightweight, quick-detach mount lets you install and remove your Aimpoint Micro series red dot in seconds. Replaces original factory base and secures to the Aimpoint sight with four, high-strength, steel Torx® screws for a tight hold under heavy recoil. Mounts T-1 red dot at lowest height.
SPECS: 6061 T6 aluminum, hardcoat T3 mil-spec anodized, matte black. Height measured from top of rail to bottom of scope body - .31” (7.8mm). Fits Aimpoint Micro series red dot sights only.
Mehr...
Felsenfeste Montage
Leichte, schnell abnehmbare Montage, mit der du dein Aimpoint Micro Serie Rotpunktvisier in Sekunden anbringen und entfernen kannst. Ersetzt die originale Werkshalterung und wird mit vier hochfesten Stahl Torx® Schrauben am Aimpoint Visier befestigt, um auch bei starkem Rückstoß einen festen Halt zu gewährleisten. Montiert das T-1 Rotpunktvisier in der niedrigsten Höhe.
SPECS: 6061 T6 Aluminium, hartbeschichtet T3 mil-spec eloxiert, matt schwarz. Höhe gemessen von der Oberkante der Schiene bis zum unteren Rand des Zielfernrohrkörpers - .31” (7,8mm). Passt nur auf Aimpoint Micro Serie Rotpunktvisiere.
Mehr...
Kundenbewertungen zu AMERICAN DEFENSE MANUFACTURING Aimpoint Micro CAS-V Mounts, Standard Latch
Anzahl der Bewertungen: 4
Von brownells.com: 4
Durchschnittliche Bewertung: 4,5
works great with Sig Romeo5(05.11.2017)
Works well in conjunction with a fixed front sight post and allows a less obstructed view. Is secure and comes off quickly and does not add much weight. About 7.5 oz for the sight and base.
Great mount(09.01.2016)
I purchased this for my Aimpoint H1 and I am more than pleased with it. Sturdy mount, easy to install, and takes a beating in training. Highly recommend.
solid mount(30.08.2011)
I've used a couple of these mounts, the AD-T1-10 provides an absolute cowitness with flattop AR's. Overall I'm happy with these, they are solid and lock up tight, a good value for the money. This particular model is the low model for using on shotguns, pistols, etc. [...] I was going to go with a larue, but the I beam design they use on their absolute cowitness model looks flimsy to me.
mounted on AK(21.11.2015)
I used this to mount an Aimpoint T1 on my Maadi AK. When attached to the Ultimak gas tube I cannot see the enough of the iron sights to use them effectively - my reason for 4 stars. Otherwise, the mount is sturdy, easy to remove and it's American made.