Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Trijicon RMR red dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Flat Head Cap Screws - Provided for Trijicon RMR The screws that are included with this mount require a 5/64'' allen wrench for installation. This mount does not fit: Sig P320 RX Sig P320 X-Five (with Romeo1 cut) Sig M17 Military Surplus
Mehr...
Entferne einfach das hintere Visier deiner Waffe und ersetze es durch die EGW Montage, um dein Trijicon RMR Red-Dot-Visier anzubringen. Du kannst die Montage jederzeit abnehmen und dein hinteres Visier wieder einsetzen. Montagematerial inklusive. Installationsanleitung Entferne das hintere Visier* Installiere die EGW Sight Mount in der Schwanzschraube Ziehe die Madenschraube fest (falls zutreffend) Platziere das Red-Dot-Visier auf der EGW Sight Mount (ein kleines Stück Papier zwischen dem Red-Dot-Visier und der Sight Mount erleichtert die Demontage und schützt vor Loctite am Red-Dot-Visier.) Trage blaues Loctite auf die mitgelieferten Montageschrauben auf Ziehe die Montageschrauben mit einem Drehmoment von 15in/lbs fest 2 Flachkopfschrauben - für Trijicon RMR bereitgestellt Die bei dieser Montage mitgelieferten Schrauben benötigen einen 5/64''-Inbusschlüssel zur Installation. Diese Montage passt nicht für: Sig P320 RX Sig P320 X-Five (mit Romeo1 Ausschnitt) Sig M17 Military Surplus
Mehr...
76.976.91EUR
Artikel-Nr.: 296000707 EGW OPTIC READY ADAPTER PLATE FOR TRIJICON RMR FITS SIG M17 BLK Herstellerproduktnummer: 49500841370112135 Entferne einfach das hintere Visier deiner Waffe und ersetze es durch die EGW Montage, um dein Trijicon RMR Red-Dot-Visier anzubringen. Du kannst die Montage jederzeit abnehmen und dein hinteres Visier wieder einsetzen. Montagematerial inklusive. Installationsanleitung Entferne das hintere Visier* Installiere die EGW Sight Mount in der Schwanzschraube Ziehe die Madenschraube fest (falls zutreffend) Platziere das Red-Dot-Visier auf der EGW Sight Mount (ein kleines Stück Papier zwischen dem Red-Dot-Visier und der Sight Mount erleichtert die Demontage und schützt vor Loctite am Red-Dot-Visier.) Trage blaues Loctite auf die mitgelieferten Montageschrauben auf Ziehe die Montageschrauben mit einem Drehmoment von 15in/lbs fest 2 Flachkopfschrauben - für Trijicon RMR bereitgestellt Die bei dieser Montage mitgelieferten Schrauben benötigen einen 5/64''-Inbusschlüssel zur Installation. Diese Montage passt nicht für: Sig P320 RX Sig P320 X-Five (mit Romeo1 Ausschnitt) Sig M17 Military Surplus
Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Trijicon RMR red dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Flat Head Cap Screws - Provided for Trijicon RMR The screws that are included with this mount require a 5/64'' allen wrench for installation. This mount does not fit: Sig P320 RX Sig P320 X-Five (with Romeo1 cut) Sig M17 Military Surplus
Mehr...
Entferne einfach das hintere Visier deiner Waffe und ersetze es durch die EGW Montage, um dein Trijicon RMR Red-Dot-Visier anzubringen. Du kannst die Montage jederzeit abnehmen und dein hinteres Visier wieder einsetzen. Montagematerial inklusive. Installationsanleitung Entferne das hintere Visier* Installiere die EGW Sight Mount in der Schwanzschraube Ziehe die Madenschraube fest (falls zutreffend) Platziere das Red-Dot-Visier auf der EGW Sight Mount (ein kleines Stück Papier zwischen dem Red-Dot-Visier und der Sight Mount erleichtert die Demontage und schützt vor Loctite am Red-Dot-Visier.) Trage blaues Loctite auf die mitgelieferten Montageschrauben auf Ziehe die Montageschrauben mit einem Drehmoment von 15in/lbs fest 2 Flachkopfschrauben - für Trijicon RMR bereitgestellt Die bei dieser Montage mitgelieferten Schrauben benötigen einen 5/64''-Inbusschlüssel zur Installation. Diese Montage passt nicht für: Sig P320 RX Sig P320 X-Five (mit Romeo1 Ausschnitt) Sig M17 Military Surplus